Tel：+86 710 311 8989
Fax：+86 710 346 7330
Email：sales@feng-shen.com
Address：The 2nd JiaWa Industrial Park, No.19 RenMin Rd,XiangYang City,HuBei Province,441000 China.
Silicone Sealant
Position：Home > Products > Electronic Adhesive > Silicone Sealant >Silicone encapsulants series
The silicone sealant for sealing electronic component industry, circuit board etc.. Able to form a transparent protective film in a variety of printed circuit board, prevent moisture erosion leads to leakage and short, can prevent the weak acid and alkali, alcohol and mold and salt spray, this product is high temperature resistant, heat will not drop. This product is waterproof, moisture-proof, main functions: shockproof, anti mechanical damage, improve the insulation strength, shielded wire, cable, wire connectors, switch box and air contact. Can also be used for corona TV can prevent high-pressure components such as leakage caused. Also can prevent anger over high frequency antenna transmission equipment, electronic devices from the erosion of salt mist.
封神有机硅灌封胶系列：
The silicone sealant series:
FS-9100PCB高温防潮胶
FS-9100PCB high temperature curing adhesive
一、产品说明
A, product description
PCB高温防潮胶是专门为PCB板等领域的灌封保护而设计的单组份、低模量、中性固化的有机硅弹性密封胶。
PCB high temperature curing adhesive is silicone elastic sealant for sealing protection of PCB plate in areas such as design component, low modulus, neutral cure.
二、产品特性
Two, the characteristics of the product
◆. 粘度低，流淌性好，操作方便;
◆. Low viscosity, good flowing property, convenient operation;
◆. 优越的耐气候老化性能,耐黄变,防潮防水性能优越;
◆. Excellent weathering performance, yellowing resistance, moisture-proof and waterproof superior performance;
◆. 耐高低温性能优越,在-50℃~+180℃范围内性能变化不大,可长期使用;
◆. High temperature resistant is superior, in -50 ℃ ~+180 ℃ properties changed little, can be used for a long time;
◆. 固化后无毒，吸附性好;
◆. After curing, non-toxic, good adsorption performance;
三、产品技术参数
Three technical parameters, product
典型技术参数
Typical technical parameter
|
颜色 |
透明，白色或黑色 |
粘度 |
1000±100 |
|
比重 |
1.0～ |
硬度（邵氏A） |
20～25 |
|
抗拉强度 |
0.8MPa |
剪切强度 |
1.0MPa |
|
断裂伸长率 |
200% |
使用温度范围 |
-50～ |
|
击穿电压 |
20Kv/mm |
体积电阻率 |
≥1×1015Ω*CM |
|
介电常数 |
2.8（1MHz） |
表干时间 |
180 分钟（ |
Four, the use of methods
◆确定基材
◆ determine substrate
首先排除不能确定的因素，如：某些金属镀层和漆层。
First rule out the factors, such as: not sure of some metal coating and the paint layer.
清除需要施胶部位的松散层。如果有镀层或漆层，应确定有足够的附着力。
Remove loose layer sizing parts. If the coating or paint layer, should determine the adequate adhesion.
若附着力不强可使用专门清洗剂清洗待施胶部位，使其干净、坚硬、干燥并无油脂及表面脏污如脱模剂，养护薄膜和疏水剂等杂物。
If the adhesion is not strong can use special cleaning agent for sizing parts, make it clean, hard, dry and free of grease and surface dirt such as releasing agent, curing film and hydrophobic agent etc..
◆施胶
◆ sizing
视PCB板大小选择合适的刷板直接刷涂，也可直接倾倒。流淌后可自动消泡。多余的胶液在其固化前处理干净。部件在3小时后可进入下一道工序。24小时后达到最大强度（环境温度太低会导致表干时间和固化时间有所减慢）。
As the PCB board size selection of appropriate coating brush brush plate directly, can also direct dumping. Flow can be automatically defoaming. The redundant glue in the curing processing clean. Components in 3 hours after entering the next procedure. Maximum strength after 24 hours (ambient temperature is too low will cause the surface dry time and curing time slowed down).
硫化后，残留的胶膜可用锋利的小刀削去，但不允许用手强行撕扯。
After curing, the residual film use a knife to cut, but are not allowed to use hand to tear.
五、储存及有效期
Five, storage and shelf life
属于非危险品，请储存于温度在30℃以下的阴凉干燥处，有效期为12个月，使用完后应注意密封，因密封不良导致表面有轻微胶皮的挑去胶皮即可，不影响使用。
Belong to non dangerous goods, please store in temperature at 30 ℃ in a cool and dry place, valid for a period of 12 months, using the seal should be finished, because of bad sealing surface has a slight lead rubber rubber can be picked to go, does not affect the use.
六、注意事项
In six, the matters needing attention
本产品完全固化后无毒性,但固化前应避免与眼睛、小孩接触；
This product is completely solidified non-toxic, but should avoid contact with eyes, the child before curing;
FS-9101 electronic potting
一、产品说明
A, product description
电子灌封胶是专门为LED、电路板及排线等的灌封保护而设计的单组份、低模量、中性快速固化的有机硅弹性密封胶。
Electronic potting is silicone elastic sealant for sealing protection LED, circuit board and cable etc. and the design of the single component, low modulus, neutral curing.
二、产品特性
Two, the characteristics of the product
◆. 粘度适中，流淌性好，操作方便，透明度高;
◆. Moderate viscosity, good flowing property, convenient operation, high transparency;
◆. 优越的耐气候老化性能,耐黄变,防潮防水性能优越;
◆. Excellent weathering performance, yellowing resistance, moisture-proof and waterproof superior performance;
◆. 柔韧性佳，耐弯折;
◆. Excellent toughness, resistance to bending;
◆. 耐高低温性能优越,在-50℃~+250℃范围内性能变化不大,可长期使用;
◆. High temperature resistant is superior, in -50 ℃ ~+250 ℃ properties changed little, can be used for a long time;
◆. 固化后无毒，吸附性好;
◆. After curing, non-toxic, good adsorption performance;
三、产品技术参数
Three technical parameters, product
典型技术参数
Typical technical parameter
|
颜色 |
透明 |
粘度 |
10000±500 |
|
比重 |
1.0～ |
硬度（邵氏A） |
20～25 |
|
抗拉强度 |
0.8MPa |
剪切强度 |
1.0MPa |
|
断裂伸长率 |
200% |
使用温度范围 |
-50～ |
|
击穿电压 |
20Kv/mm |
体积电阻率 |
≥1×1015Ω*CM |
|
介电常数 |
2.8（1MHz） |
表干时间 |
5分钟（ |
Four, the use of methods
◆确定基材
◆ determine substrate
首先排除不能确定的因素，如：某些金属镀层和漆层。
First rule out the factors, such as: not sure of some metal coating and the paint layer.
清除需要施胶部位的松散层。如果有镀层或漆层，应确定有足够的附着力。
Remove loose layer sizing parts. If the coating or paint layer, should determine the adequate adhesion.
若附着力不强可使用专门清洗剂清洗待施胶部位，使其干净、坚硬、干燥并无油脂及表面脏污如脱模剂，养护薄膜和疏水剂等杂物。
If the adhesion is not strong can use special cleaning agent for sizing parts, make it clean, hard, dry and free of grease and surface dirt such as releasing agent, curing film and hydrophobic agent etc..
◆施胶
◆ sizing
直接倾倒。流淌后可自动消泡。多余的胶液在其固化前处理干净。部件在3小时后可进入下一道工序。24小时后达到最大强度（环境温度太低会导致表干时间和固化时间有所减慢）。
Direct dumping. Flow can be automatically defoaming. The redundant glue in the curing processing clean. Components in 3 hours after entering the next procedure. Maximum strength after 24 hours (ambient temperature is too low will cause the surface dry time and curing time slowed down).
硫化后，残留的胶膜可用锋利的小刀削去，但不允许用手强行撕扯。
After curing, the residual film use a knife to cut, but are not allowed to use hand to tear.
五、储存及有效期
Five, storage and shelf life
属于非危险品，请储存于温度在30℃以下的阴凉干燥处，有效期为12个月，使用完后应注意密封，因密封不良导致表面有轻微胶皮的挑去胶皮即可，不影响使用。
Belong to non dangerous goods, please store in temperature at 30 ℃ in a cool and dry place, valid for a period of 12 months, using the seal should be finished, because of bad sealing surface has a slight lead rubber rubber can be picked to go, does not affect the use.
六、注意事项
In six, the matters needing attention
本产品完全固化后无毒性,但固化前应避免与眼睛、小孩接触;
This product is completely solidified non-toxic, but should avoid contact with eyes, the child before curing;
FS-9102电子灌封胶
FS-9102 electronic potting
一、产品说明
A, product description
电子灌封胶是专门为电子元器件、发光二极管、电气模块等的灌封保护而设计的单组份、低模量、中性固化的有机硅弹性密封胶。
Electronic potting is silicone elastic sealant for sealing protection of electronic components, electrical, light emitting diode module and the design of single component, low modulus, neutral cure.
二、产品特性
Two, the characteristics of the product
◆. 粘度适中，流淌性好，操作方便;
◆. Moderate viscosity, good flowing property, convenient operation;
◆. 优越的耐气候老化性能,耐黄变,防潮防水性能优越;
◆. Excellent weathering performance, yellowing resistance, moisture-proof and waterproof superior performance;
◆. 柔韧性佳，耐弯折，弹性好;
◆. Excellent toughness, bending resistance, good elasticity;
◆. 耐高低温性能优越,在-50℃~+250℃范围内性能变化不大,可长期使用;
◆. High temperature resistant is superior, in -50 ℃ ~+250 ℃ properties changed little, can be used for a long time;
◆. 固化后无毒，吸附性好，耐化学介质;
◆. After curing, non-toxic, good adsorption, chemical resistant;
三、产品技术参数
Three technical parameters, product
典型技术参数
Typical technical parameter
|
颜色 |
透明、半透明、白色、黑色 |
粘度 |
10000±500 |
|
比重 |
1.0～ |
硬度（邵氏A） |
20～25 |
|
抗拉强度 |
>0.5MPa |
剪切强度 |
>0.5MPa |
|
断裂伸长率 |
250% |
使用温度范围 |
-50～ |
|
击穿电压 |
20Kv/mm |
体积电阻率 |
≥5×1016Ω*CM |
|
介电常数 |
2.8（1MHz） |
表干时间 |
30分钟（ |
Four, the use of methods
◆确定基材
◆ determine substrate
清除需要施胶部位的松散层。如果有镀层或漆层，应确定有足够的附着力。
Remove loose layer sizing parts. If the coating or paint layer, should determine the adequate adhesion.
若附着力不强可使用专门清洗剂清洗待施胶部位，使其干净、坚硬、干燥并无油脂及表面脏污如脱模剂，养护薄膜和疏水剂等杂物。
If the adhesion is not strong can use special cleaning agent for sizing parts, make it clean, hard, dry and free of grease and surface dirt such as releasing agent, curing film and hydrophobic agent etc..
◆施胶
◆ sizing
直接倾倒。流淌后可自动消泡。多余的胶液在其固化前处理干净。部件在3小时后可进入下一道工序（环境温度太低会导致表干时间和固化时间有所减慢）。
Direct dumping. Flow can be automatically defoaming. The redundant glue in the curing processing clean. Components in 3 hours after entering the next procedure (ambient temperature is too low will cause the surface dry time and curing time slowed down).
硫化后，残留的胶膜可用锋利的小刀削去，但不允许用手强行撕扯。
After curing, the residual film use a knife to cut, but are not allowed to use hand to tear.
五、储存及有效期
Five, storage and shelf life
属于非危险品，请储存于温度在30℃以下的阴凉干燥处，有效期为12个月，使用完后应注意密封，因密封不良导致表面有轻微胶皮的挑去胶皮即可，不影响使用。
Belong to non dangerous goods, please store in temperature at 30 ℃ in a cool and dry place, valid for a period of 12 months, using the seal should be finished, because of bad sealing surface has a slight lead rubber rubber can be picked to go, does not affect the use.
六、注意事项
In six, the matters needing attention
本产品完全固化后无毒性,但固化前应避免与眼睛、小孩接触;
This product is completely solidified non-toxic, but should avoid contact with eyes, the child before curing;
FS-9102B电子灌封胶
FS-9102B electronic potting
一、产品说明
A, product description
电子灌封胶是专门为需要耐高温的电子元器件的灌封保护而设计的单组份、低模量、中性固化的有机硅弹性密封胶。
Electronic potting potting protection of electronic components is tailored to the needs of high temperature resistance and the design of single component, low modulus, neutral cure silicone elastic sealant.
二、产品特性
Two, the characteristics of the product
◆. 粘度适中，流淌性好，操作方便;
◆. Moderate viscosity, good flowing property, convenient operation;
◆. 优越的耐气候老化性能,耐黄变,防潮防水性能优越;
◆. Excellent weathering performance, yellowing resistance, moisture-proof and waterproof superior performance;
◆. 柔韧性佳，耐弯折，弹性好，强度高;
◆. Excellent toughness, bending resistance, good elasticity, high strength;
◆. 耐高低温性能优越,在-50℃~+250℃范围内性能变化不大,可长期使用;
◆. High temperature resistant is superior, in -50 ℃ ~+250 ℃ properties changed little, can be used for a long time;
◆. 固化后无毒，吸附性好，耐化学介质;
◆. After curing, non-toxic, good adsorption, chemical resistant;
三、产品技术参数
Three technical parameters, product
典型技术参数
Typical technical parameter
|
颜色 |
白色、黑色、红色 |
粘度 |
10000±500 |
|
比重 |
1.0～ |
硬度（邵氏A） |
25～30 |
|
抗拉强度 |
>1.5MPa |
剪切强度 |
>1.0MPa |
|
断裂伸长率 |
250% |
使用温度范围 |
-50～ |
|
击穿电压 |
20Kv/mm |
体积电阻率 |
≥5×1016Ω*CM |
|
介电常数 |
2.8（1MHz） |
表干时间 |
30分钟（ |
Four, the use of methods
◆确定基材
◆ determine substrate
清除需要施胶部位的松散层。如果有镀层或漆层，应确定有足够的附着力。
Remove loose layer sizing parts. If the coating or paint layer, should determine the adequate adhesion.
若附着力不强可使用专门清洗剂清洗待施胶部位，使其干净、坚硬、干燥并无油脂及表面脏污如脱模剂，养护薄膜和疏水剂等杂物。
If the adhesion is not strong can use special cleaning agent for sizing parts, make it clean, hard, dry and free of grease and surface dirt such as releasing agent, curing film and hydrophobic agent etc..
◆施胶
◆ sizing
直接倾倒。流淌后可自动消泡。多余的胶液在其固化前处理干净。部件在3小时后可进入下一道工序（环境温度太低会导致表干时间和固化时间有所减慢）。
Direct dumping. Flow can be automatically defoaming. The redundant glue in the curing processing clean. Components in 3 hours after entering the next procedure (ambient temperature is too low will cause the surface dry time and curing time slowed down).
硫化后，残留的胶膜可用锋利的小刀削去，但不允许用手强行撕扯。
After curing, the residual film use a knife to cut, but are not allowed to use hand to tear.
五、储存及有效期
Five, storage and shelf life
属于非危险品，请储存于温度在30℃以下的阴凉干燥处，有效期为12个月，使用完后应注意密封，因密封不良导致表面有轻微胶皮的挑去胶皮即可，不影响使用。
Belong to non dangerous goods, please store in temperature at 30 ℃ in a cool and dry place, valid for a period of 12 months, using the seal should be finished, because of bad sealing surface has a slight lead rubber rubber can be picked to go, does not affect the use.
六、注意事项
In six, the matters needing attention
本产品完全固化后无毒性,但固化前应避免与眼睛、小孩接触;
This product is completely solidified non-toxic, but should avoid contact with eyes, the child before curing;
FS-9103双组份灌封胶
FS-9103 two-component sealant
一、产品说明
A, product description
双组份灌封胶是专门为灌封厚度较大的电子元器件、模块、线路板的灌封保护而设计的中性固化的有机硅弹性密封胶。
A two-component sealant is specially protected for potting potting greater thickness of electronic components, modules, circuit board and flexible silicone sealant neutral curing of the design.
二、产品特性
Two, the characteristics of the product
◆. 粘度低，流淌性好，操作方便;
◆. Low viscosity, good flowing property, convenient operation;
◆. 优越的耐气候老化性能,耐黄变,防潮防水性能优越
◆. Excellent weathering performance, yellowing resistance, moisture-proof and waterproof superior performance
◆. 深层固化性能好，柔韧性佳，耐弯折，弹性好，强度高;
◆. Deep curing performance, excellent toughness, bending resistance, good elasticity, high strength;
◆. 耐高低温性能优越,在-50℃~+250℃范围内性能变化不大,可长期使用;
◆. High temperature resistant is superior, in -50 ℃ ~+250 ℃ properties changed little, can be used for a long time;
◆. 固化后无毒，对大多数塑料均有吸附性好，耐化学介质;
◆. After curing, non-toxic, for the majority of plastic has good adsorption, chemical resistant;
三、产品技术参数
Three technical parameters, product
典型技术参数
Typical technical parameter
|
固化前 |
颜色 |
白色、黑色、红色 |
粘度 |
2000±100 |
|
比重 |
1.0～ |
固化剂加入比例 |
10% |
|
|
固化后 |
混合后粘度 |
1200±100 |
邵氏A硬度 |
15～20 |
|
线收缩率 |
0.5% |
使用温度范围 |
-50～ |
|
|
击穿电压 |
20Kv/mm |
体积电阻率 |
≥5×1016Ω*CM |
|
|
介电常数 |
2.8（100KHz） |
初步固化时间 |
3H（ |
Four, the use of methods
计量：准确称量A组份和B组份（固化剂）。
Measurement: accurate weighing of component A and component B (curing agent).
搅拌：将B组份加入装有A组份的容器中混合均匀。
Mixing: the B component to a A component containers are evenly mixed.
灌封：把混合好的胶料尽快灌封到需要灌封的产品中。
Filling: mix glue good as soon as possible to the potting potting products.
固化：灌封好的制件置于室温下固化，初固后进入下道工序，完全固化需10～24小时。
Curing: curing and good product at room temperature, the beginning of solid to the next step, to be fully cured 10 ~ 24 hours.
硫化后，残留的胶膜可用锋利的小刀削去，但不允许用手强行撕扯。
After curing, the residual film use a knife to cut, but are not allowed to use hand to tear.
五、储存及有效期
Five, storage and shelf life
属于非危险品，请储存于温度在30℃以下的阴凉干燥处，有效期为12个月，使用完后应注意密封，因密封不良导致表面有轻微胶皮的挑去胶皮即可，不影响使用。
Belong to non dangerous goods, please store in temperature at 30 ℃ in a cool and dry place, valid for a period of 12 months, using the seal should be finished, because of bad sealing surface has a slight lead rubber rubber can be picked to go, does not affect the use.
六、注意事项
In six, the matters needing attention
本产品完全固化后无毒性,但固化前应避免与眼睛、小孩接触;
This product is completely solidified non-toxic, but should avoid contact with eyes, the child before curing;
FS-9104加成型有机硅灌封胶
FS-9104 addition silicone sealant
一、产品说明
A, product description
加成型有机硅灌封胶是专门用于自由控制固化时间的产品的灌封保护而设计的可起到防水防潮防气体污染的双组份有机硅弹性密封胶。
Addition type silicone sealant is a two-component silicone elastic sealant for sealing protection of freedom control the curing time of the product design can play a waterproof anti air pollution.
二、产品特性
Two, the characteristics of the product
◆. 双组份，可操作时间长，加热后固化快，固化时间自由控制;
◆. Two component, long operating time, heated fast curing, the curing time of free control;
◆. 固化后无副产物，无收缩。
◆. No by-product after curing, no shrinkage.
◆. 固化后呈半凝固态，粘接性和密封性好，抗应力性能极强;
◆. After curing is a semi solidified, adhesion and good sealing performance, strong anti stress force performance;
◆. 固化后电气性能和耐高低温性能优越;
◆. After curing temperature performance and superior electrical performance;
◆. 固化后受外力开裂后可自动愈合，不影响后期效果;
◆. After curing force cracking can be automatic healing, has no effect on the later effect;
三、产品技术参数
Three technical parameters, product
典型技术参数
Typical technical parameter
|
固化前 |
颜色 |
透明 |
粘度 |
1000±100 |
|
比重 |
1.0～ |
固化剂加入比例 |
1:1 |
|
|
固化后 |
混合后粘度 |
1000±100 |
击穿电压 |
16Kv/mm |
|
体积电阻率 |
≥1×1015Ω*CM |
固化条件
℃/min |
25/360或80/30 |
|
|
介电常数 |
2.8（100KHz） |
Four, the use of methods
计量：准确称量A组份和B组份。
Measurement: accurate weighing of component A and component B.
搅拌：将B组份加入装有A组份的容器中混合均匀。
Mixing: the B component to a A component containers are evenly mixed.
灌封：把混合好的胶料尽快灌封到需要灌封的产品中。
Filling: mix glue good as soon as possible to the potting potting products.
固化：灌封好的制件置于室温下固化或加热80度固化。
Curing: potting good parts at room temperature curing or 80 degree heat curing.
硫化后，残留的胶膜可用锋利的小刀削去，但不允许用手强行撕扯。
After curing, the residual film use a knife to cut, but are not allowed to use hand to tear.
注：某些情况会导致有机硅凝胶不能固化，用溶剂清洗表面可避免以上情况
Note: in some cases will lead to silicone gel can not be cured, use solvents to clean the surface can avoid the above situation
接触以下化学物质会使有机硅凝胶不固化
Contact the following chemical substances will not cured silicone gel
--有机锡化合物及含有机锡的硅橡胶
Silicone rubber, organotin compounds and organotin containing
--硫磺、硫化物以及含硫的橡胶等材料
Materials: sulfur, sulfide and sulfur rubber etc.
--胺类化合物及含胺的材料
- amine compounds and materials containing amine