FS587减速机专用密封胶是专门用于减速机壳体间等的密封粘接，其独特的特性能够保证减速机长期处于良好的工作状态。
FS587 reducer special sealant is specially used for bonding, sealing the housing slowdown, its unique characteristics to ensure long-term working in good condition.
二、产品特性
Two, the characteristics of the product
◆. 单组分中性固化,无腐蚀,对铝、铜、不锈钢等多种金属和非金属材料PC;ABS等工程塑料具有良好的粘接性.
◆. Single component neutral curing, no corrosion to copper, stainless steel, aluminum, and other metal and non metal material PC; ABS engineering plastics with good adhesion
◆. 防水、防油、抗冲击、抗振动，使用后不易开裂导致泄漏；
◆. Waterproof, anti oil, anti impact, anti vibration, use no cracking cause leakage;
◆. 电阻性优越，耐热性能好，一般使用温度范围-60℃～200℃;
◆. Resistance is superior, good heat resistance, the general use of the temperature range of -60 ℃ ~ 200 ℃;
三、产品技术参数
Three technical parameters, product
|
color |
black,blue,grey |
viscosity |
paste |
|
proportion |
1.2～ |
hardness（Shao A） |
20～40 |
|
tensil strength |
1.8～2.0MPa |
shear strength |
1.0MPa |
|
volume resistance |
1×1014Ω*CM |
temperature range |
-60～ |
|
Tensile elongation rate |
200% |
surface curing time |
30mins（ |
Four, the use of methods
◆确定基材
◆ determine substrate
清除需要施胶部位的松散层。如果有镀层或漆层，应确定有足够的附着力。若附着力不够可用相关工具如钢丝球等清理待施胶部位，使其干净、坚硬、干燥并无油脂及表面脏污如脱模剂，养护薄膜和疏水剂等杂物。
Remove loose layer sizing parts. If the coating or paint layer, should determine the adequate adhesion. If the adhesion is not enough available tools such as steel wire cleaning for sizing parts, make it clean, hard, dry and free of grease and surface dirt such as releasing agent, curing film and hydrophobic agent etc..
◆施胶
◆ sizing
视结合面与间隙大小切取挤胶嘴，将其均匀挤出，涂布量用挤胶嘴孔大小控制，以结合面组合后微微挤出一胶圈为宜。 结合面涂布密封垫后，在活性期内迅速组合紧固，通常从挤胶到组合的时间间隔应越短越好，以免硫化表干而不能使用。
As the binding surface and the gap size cut from the dispensing nozzle, the uniform extrusion, coating weight with a dispensing nozzle hole size control, combined with surface combination with extrusion of a rubber ring is appropriate. Combined with surface coated gasket, quickly combined fastening in the active period, usually from the adhesive to the combination of the time interval should be as short as possible, so as not to cure table dry and not use.
硫化后，残留在结合面上的液态密封垫可用锋利的小刀削去流失到结合面外面胶膜，但不允许用手强行撕扯。还可用沾有汽油的棉纱擦去。
After curing, the residual in combination with liquid on the surface of the sealing pad use a knife to cut loss to the binding surface outside the film, but are not allowed to use hand to tear. Also available with gasoline cotton wipe.
五、储存及有效期
Five, storage and shelf life
属于非危险品，请储存于温度在27℃以下的阴凉干燥处，有效期为一年。
Belong to non dangerous goods, please store in temperature at 27 ℃ in a cool and dry place, valid for one year.
六、注意事项
In six, the matters needing attention
本产品完全固化后无毒性,但固化前应避免与眼睛、小孩接触;工作环境区域注意保持通风.
This product is completely solidified non-toxic, but should avoid contact with eyes, the child before curing; work environment to keep ventilation.